12VDC Power Supply 150W 10A Single Output Switching Meanwell LPV-150-12

Specifications

#12VDC Power Supply 150W 10A Single Output Switching Meanwell LPV-150-12

Specification Datasheet	Meanwell Power Supply LPV-150-12

#Output	DC Voltage	12V
Working Voltage	Rated Current	10A
	Current Range	0~10A
	Rated Power	120W
	Ripple Noise (max. Note.2	120mVp-p
	Voltage TOLERANCE Note.3	±5.0%
	LINE REGULATION	±1.0%
	LOAD REGULATION	±2.0%
	SETUP, RISE TIME Note.6	LPV-150: 500ms, 50ms / 230VAC 500ms, 50ms / 277VAC
	HOLD UP TIME (Typ.)	LPV-150: 18ms/230VAC 20ms/277VAC at full load

#Input	VOLTAGE RANGE Note.4	180 ~ 305VAC 254 ~ 431VDC
	FREQUENCY RANGE	47 ~ 63Hz
	EFFICIENCY (Typ.)	87%
	AC CURRENT	1.7A/230VAC 1.5A/277VAC
	INRUSH CURRENT(Typ.)	Blank type COLD START 60A(twidth=900μs measured at 50% Ipeak) at 230VAC L type COLD START 75A(twidth=900μs measured at 50% Ipeak) at 115VAC
	MAX. No. of PSUs on 16A CIRCUIT BREAKER.	Blank type 2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC L type 1 units (circuit breaker of type B) / 2 units (circuit breaker of type C) at 115VAC
	LEAKAGE CURRENT	0.25mA / 240VAC

#Protection	Over Load	110 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed
	Over Voltage	13.5 ~ 18V Protection type : Shut down o/p voltage, re-power on to recover

#Environment	WORKING TEMP.	-25 ~ +70°C (Refer to "Derating Curve")
	WORKING HUMIDITY	20~90% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40~+80°C, 10~ 95% RH
	TEMP. COEFFICIENT	±0.03%/°C (0 ~ 40°C for LPV-150-12
	VIBRATION	10~500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

#Safety & EMC Standards	SAFETY STANDARDS	UL8750,CSA C22.2 No 250.13-12,UL879,CSA C22.2 No.207-M89,BIS IS15885(for LPV-150-12,24 only),EAC TP TC 004, IP67, IEC62368-1, BS EN/EN62368-1 approved
	WITHSTAND VOLTAGE	I/P-O/P: 3KVAC
	ISOLATION RESISTANCE	I/P-0/P:>100M Ohms / 500VDC/25°C/ 70% RH
	EMC EMISSION	Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2 Class A(≤80% load), BS EN/EN61000-3-3, EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN55035, light industry level, EAC TP TC 020

	MTBF	3361.2K hrs min. Telcordia SR-332 (Bellcore) ; 391.9Khrs min. MIL-HDBK-217F (25°C)
	DIMENSION	1916337.5mm (LWH)
	PACKING	LPV-150: 0.74Kg;20pcs/15.8Kg/0.95CUFT

Note		1. All parameters NOT specially mentioned are measured at 230VAC(115VAC for LPVL) input, rated load and 25°C of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
		3. Tolerance : includes set up tolerance, line regulation and load regulation.
		4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
		5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
		(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
		6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
		7. Suitable for indoor use or outdoor use without direct sunlight exposure.
		8. The ambient temperature derating of 3.5°C/1000m with fanless models and of 5°C/1000m with fan models for operating altitude higher than 2000m(6500ft). 9. For any application note and IP water proof function installation caution, please refer our user manual before using.
		https://www.meanwell.com/Upload/PDF/LED_EN.pdf
		10. This product is not intended for LED lighting luminaire applications in the EU.(In the EU the LPF/NPF/XLG series are recommended.) ※ Product Liability Disclaimer:For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx